Description
John Deere Controller RE551415 L21 – Engine Controller Repair Service
This John Deere Controller RE551415 L21 page covers the repair service for the L21 engine control module, part number RE551415. First, you ship the unit to our lab. Then, we diagnose it, repair the board, and test it on the bench. As a result, you receive your own module back, already matched to your machine.
The module is returned fully reconditioned and tested. In addition, it keeps the original calibration and serial data of your equipment. Therefore, you avoid buying a new module and paying for programming. Finally, this page explains the price policy, the warranty, and the shipping process.
Diagnostic fee and refund policy
If the control module is not repairable, a diagnostic fee of $350 will be charged and the remaining balance will be refunded. First, we run a complete diagnosis of the board. Then, if the module can be repaired, the full service price applies. However, if the board is beyond repair, you only pay the $350 diagnostic fee. As a result, the difference is refunded to your original payment method.
What the L21 engine controller does
The L21 module manages fuel injection, injector timing, and engine protection. It also reads the sensors for pressure, temperature, and speed. In addition, it communicates with the display and the transmission over the CAN bus. For example, when the module fails, the engine may not start or may shut down without warning.
Common failures of the John Deere Controller RE551415 L21
Many units arrive with blown fuses, no communication, or the engine shutting down. Others show fault codes stored in the unit or intermittent faults. In addition, oil intrusion and water damage are frequent on this engine controller. Injector driver faults are also common. However, most of these failures are repairable at the board level.
Compatible John Deere equipment
This L21 controller is used in the following John Deere machines and engines. However, always compare the part number on your label with RE551415 before shipping the unit.
- 250D-II,
- 250G,
- 290G,
- 300D-II,
- 350G,
- 380G,
- 624K,
- 644K,
- 644K HYBRID,
- 670G,
- 672G,
- 724K,
- 744K,
- 750K,
- 755K,
- 770G,
- 772G,
- 850K,
- 870G,
- 872G,
- 1070E,
- 1110E,
- 1170E,
- 1210E,
- 1270E,
- 1470E,
- 1510E,
- 4940,
- 6068HFC94,
- 6068HFC95,
- 6068HFG94,
- 6068HFG95,
- 6090HFC94,
- 6090HFC95,
- 6090HFG94,
- 6090HFG95,
- 6170R,
- 6190R,
- 6210R,
- 7200R,
- 7210R,
- 7215R,
- 7230R,
- 7250R,
- 7260R,
- 7270R,
- 7280R,
- 7290R,
- 7610,
- 7710,
- 7810,
- 8235R,
- 8245R,
- 8260R,
- 8270R,
- 8285R,
- 8295R,
- 8310R,
- 8310RT,
- 8320R,
- 8320RT,
- 8335R,
- 8335RT,
- 8345R,
- 8345RT,
- 8360R,
- 8360RT,
- 8370R,
- 8370RT,
- 9360R,
- S650,
- S660,
- S660 PRECISION UPGRADES,
- S670,
- S670 PRECISION UPGRADES,
- S670H,
- T550,
- T560,
- T660,
- T670,
- W540,
- W550,
- W650,
- W660,
How we repair the John Deere Controller RE551415 L21
First, our technicians open the module and inspect the board under magnification. Then, they replace the failed drivers, capacitors, and processors with new components. In addition, every solder joint is checked and repaired when needed. As a result, the board returns to factory electrical specifications. Finally, the housing is sealed again to protect it from oil and water.
Bench testing before shipping
Every repaired unit runs on our simulation bench before it leaves the lab. First, we apply power and verify communication with the diagnostic tool. Then, we simulate the engine sensors and check the injector outputs. However, we do not stop there. We also run heat cycles to detect intermittent faults. As a result, the module is tested under real operating conditions.
What you receive with the John Deere Controller RE551415 L21 service
You receive your own module, repaired and tested. In addition, you receive a test report with the faults found and the work performed. The package is protected with antistatic material and foam. Finally, we send a tracking number as soon as the unit ships.
Installation and final configuration
First, disconnect the battery before installing the module. Then, mount the unit in the same position and reconnect the harness. In addition, make sure the connectors are clean and locked. However, we do not promise a guaranteed plug and play result. The final configuration on site is completed by a specialized technician. For example, some machines require a reset of fault codes with a scan tool.
Warranty and technical support
The repair comes with a one year warranty. In addition, our engineers provide technical assistance during installation. If you have questions, send us an email or call our office. Finally, keep your invoice, because it is required for any warranty claim.
How to order the John Deere Controller RE551415 L21 repair step by step
First, confirm that your part number is RE551415. Then, add the service to the cart and complete the checkout. In addition, print the order and pack the module with protective material. After that, ship the unit to our lab in Orlando, Florida. Finally, we diagnose, repair, test, and ship the module back with a tracking number.
How long does the repair take?
Diagnosis and repair usually take three to five business days after we receive the unit. Then, shipping time depends on your location. As a result, most customers receive the module back within two weeks.
What happens if the module cannot be repaired?
If the control module is not repairable, a diagnostic fee of $350 will be charged and the remaining balance will be refunded. In addition, we send you a report explaining the damage found. Therefore, you can decide the next step with real information.
Do I lose my calibration?
No. The repair keeps the original software and calibration of your module. However, if the memory is damaged, we inform you before continuing. As a result, there are no surprises at the end.
Why trust ECM Engineering
Our engineering team has more than 15 years of experience and more than 10K repaired modules. In addition, we use the latest simulation technology in our lab. As a result, you receive a module that has been tested, not just cleaned. Finally, our support team answers your questions before and after the sale.
ECM Engineering USA / ECM Repair USA
Share ON: Twitter | Facebook | Linked In | Tumblr
