Description
Volvo Penta ECM 60100017 for Volvo Penta marine engines
The Volvo Penta ECM 60100017 is a New aftermarket Volvo engine control module that we program in our own shop. First, we confirm the application you send us. Then we program the unit from scratch against your engine serial number. As a result, you receive electronic customization for your engine, not a generic part off a shelf.
This listing covers the Volvo module, part number 60100017, for Volvo Penta marine engines. Please read the sections below before you order, because every unit is prepared for one engine.
What This Volvo Penta ECM 60100017 Module Controls
The module manages fuel delivery, injection timing and emission control. In addition, it reads every sensor signal and runs the engine protection strategy. It also stores the fault codes that your diagnostic tool reads during service. For example, it logs an injector code long before the engine shows a symptom on the road.
Engine Applications and Fitment
We list this unit for Volvo Penta marine engines. However, fitment depends on your exact engine serial number. For example, two engines of the same family can carry different calibrations from the factory. Therefore, send us the serial number before you order and we confirm the match for you.
Faults It Solves
Typical symptoms are no start, derate, intermittent shutdown and loss of communication with the diagnostic tool. Water intrusion, vibration and corrosion on the board cause many of these failures. A New aftermarket Volvo module replaces the failed unit and restores the original function.
How We Program and Test the Volvo Penta ECM 60100017
First, we inspect the new unit and confirm the hardware matches your application. Then we test the power stages one by one. Finally, we load the calibration that matches your engine serial number. That final step is the electronic customization that makes the module yours.
Bench Testing Before Shipping
Every unit runs on our test bench before it leaves the shop. We simulate the sensor inputs and verify the outputs under load. As a result, you receive a module that already ran correctly before it was packed.
What You Receive
You receive the Volvo Penta ECM 60100017 programmed and bench tested, ready for installation. We ship from our facility in Orlando, Florida. In addition, the tracking number goes out the same day the unit leaves the shop.
Installation and Final Configuration
We do not promise a guaranteed plug and play result, because we do not know the specific boat where the module will be installed. Therefore, a specialized technician with original diagnostic equipment should complete any additional configuration on site.
Warranty and Support After the Sale
The module carries a 1 year warranty. In addition, our technical team supports your installer during the installation. Contact us if the engine behaves differently once the module is in place, and we review the case with you.
Ordering Process Step by Step
First, send us the engine serial number and the part number printed on your module. Then we confirm the calibration and the price. Next, we program the unit. Finally, we ship it with tracking to your address.
Frequently Asked Questions
Is the Volvo Penta ECM 60100017 plug and play?
Not in every case. We prepare it against your engine serial number before shipping. However, some machines need extra configuration that only a technician can complete on site with the engine present.
What do you need to work on the Volvo Penta ECM 60100017?
We need the engine serial number, the part number printed on your module and the software level if you have it. In addition, a photo of the label on the module helps us confirm the application.
Is this module new?
Yes. This is a New aftermarket Volvo module, not a used unit. We program it for your engine and test it before it ships, with a 1 year warranty.
How long does the process take?
Most units ship within two to three business days. However, a hard failure on the board can take longer. We confirm the date with you before you commit to the order.
Why Buy the Volvo Penta ECM 60100017 From ECM Engineering USA
We work only with engine control modules. Our bench, our tools and our experience are built around them. For example, we keep calibration files for hundreds of Volvo applications, so we can confirm your unit quickly.
ECM Engineering USA / ECM Repair USA Facebook | Linkedin | Twitter