Volvo Penta Marine | 5.7Gi-F(F), 5.7GXi-G(F) | ECM Repair

Original price was: $1,098.00.Current price is: $697.00.

Volvo Penta Marine | 5.7Gi-F(F), 5.7GXi-G(F) | ECM Repair .

Get your ECM repaired and returned fully reconditioned, tested, and ready for installation on the same engine.

Description

Volvo Penta 5.7Gi marine ECM repair | 5.7GXi-G(F)

Our bench handles your Volvo Penta 5.7Gi marine ECM repair and returns the unit ready for the water. First, you ship the module to our shop in Orlando, Florida. Then our engineers diagnose every fault on the board.

After that, we rebuild the failed sections and test under load. As a result, the module goes back on the same engine it came from.

Part numbers covered by this service

  • 21211981, 3847942 and 22083180
  • 3818613, 32502147 and 39004136
  • E2371504D, E2050001A and 3884030
  • 23414009, 3885478 and 3885461
  • 21906707, 21906864 and 024309

Volvo Penta labels this board in several ways. Therefore, read your own unit before you ship it. Also, a photo of the connector settles any doubt.

Engines covered by the Volvo Penta 5.7Gi marine ECM repair

The service covers the 5.7Gi-F(F) and the 5.7GXi-G(F) gasoline marine engines. However, serial ranges matter, so send your engine data with the module.

Maintenance that keeps the module alive

Routine care protects the board more than any repair can. First, follow the service schedule the manufacturer publishes. Then keep the connector clean and dry after every trip.

Moreover, watch for early warning signs on the dash. For example, a rough idle or a warning lamp often arrives before a full failure. Therefore, an early check saves the season.

Troubleshooting before you ship

Start with the basics on the boat. First, check the battery voltage and the ground connections. Then inspect the harness for chafed wire and green terminals.

Next, read the stored codes with a scan tool. After that, note exactly when the fault appears. As a result, our bench can reproduce the same condition.

Symptoms that bring these units to us

Most boats arrive with a familiar story. For example, the engine cuts out and restarts later. Sometimes the scan tool cannot see the module at all.

In addition, a fuse blows as soon as the key turns. A failing Volvo Penta 5.7Gi marine ECM repair often shows more than one sign. Moreover, salt air and moisture ruin the tracks over time.

Faults we correct on the bench

  • Blowing fuses
  • No communication with the scan tool
  • Engine shutting down
  • Fault codes stored in the unit
  • Intermittent faults under vibration
  • Oil intrusion
  • Water damage

However, most units carry more than one of these. Therefore, we check every circuit before we seal the case.

What happens before your Volvo Penta 5.7Gi marine ECM repair starts

We diagnose the unit first and tell you what we find. However, if the board cannot be saved, or if nothing is wrong, you hear it before any charge. In that case, we process a partial refund for the difference.

Warranty and technical support

A one year warranty backs every repair we deliver. Also, our team answers technical questions before and after the job. For example, you can describe the codes your technician reads today.

Why trust our bench

Our engineering team carries more than 15 years of experience. Furthermore, we have rebuilt over 10,000 modules to date. Our simulation equipment reproduces the real engine signals during testing.

Order your Volvo Penta 5.7Gi marine ECM repair

Ready to start? First, read our ECM repair services process. Next, browse the full marine ECM range. Finally, watch real bench tests on the ECM Engineering USA YouTube channel.

Ecm repair 4 steps

Additional information

Weight85 oz
Dimensions12 × 10 × 7 in
Volumen

width x height x depth