Caterpillar 607-2611 | ECM Repair

Original price was: $699.00.Current price is: $519.00.

Caterpillar 607-2611 | 6072611

Your Engine Control Module will be returned fully reconditioned, rigorously tested, and ready to be installed back onto the exact engine it came off, saving you the time and expense of having a new ECM programmed to your machine.

We thoroughly diagnose the unit; if it’s not repairable or no problems are found, it costs $200 plus shipping cost for return.

Description

Caterpillar 607-2611 control module repair | 6072611 ECM

Our bench handles your Caterpillar 607-2611 control module repair and returns the unit ready to work. First, you ship the module to our shop in Orlando, Florida. Then our engineers diagnose every fault on the board.

After that, we rebuild the failed sections and test under load. As a result, the controller goes back on the exact machine it came from. Moreover, you avoid the cost of programming a new unit.

Caterpillar 607-2611 control module repair service unit

Part numbers covered by this service

Two references describe the same controller. For example, 607-2611 and 6072611 both appear on these units. Therefore, check the label on your module before you ship it. Also, send a photo of the connector if you have any doubt.

Machines covered by the Caterpillar 607-2611 control module repair

The list below groups the Caterpillar families that use this controller. However, serial ranges matter, so send your machine model with the unit.

  • TRACK-TYPE TRACTORD7R II.
  • PUMPERSPF743.
  • UNDERGROUND ART TRUCKAD60, AD55B, AD45, AD63.
  • TRUCK793F, CMD, 797F, 793F, 795F, AC 794, AC 793F OEM
  • PETROLEUM TRANSMISSIONTH31-E61, CX48-P2300.

Trucks, dozers and graders also run this board. In addition, each family uses its own calibration. Therefore, we record the original data before we start.

  • WHEEL DOZER834H, 854K.
  • OFF HIGHWAY TRUCK770, 798, 794 AC, 796 AC, 798 AC.
  • LANDFILL COMPACTOR836H.
  • MOTOR GRADER14L, 16M, 12M, 150, 14M, 140M 2, 140, 160, 12M 2, 14 140M, 120M, 120K, 160M 2, 120K 2, 120M 2, 160M.
  • WHEEL LOADER993K, 988H, 994F, 994H, 992K, 993.

Caterpillar 6072611 ECM board on the test bench

Symptoms that bring these units to us

Most boards arrive with a familiar story. For example, the engine cuts out and restarts later. Sometimes the technician simply loses the link with the module.

In addition, a blown fuse returns every time the key turns. A failing Caterpillar 607-2611 control module repair often shows more than one symptom. Moreover, oil or water intrusion damages the board over time.

How our bench tests the board

First, we open the housing and inspect the tracks under magnification. Then we measure the supply rails and the output drivers.

Next, we replace the components that fail the test. After that, the board runs a full cycle on our simulator. As a result, an intermittent fault shows up before the unit leaves.

Why these controllers fail on the job

Vibration and heat work against every board on a big machine. First, the solder joints crack after thousands of hours. Then moisture reaches the tracks through a tired seal.

In addition, a weak alternator sends spikes into the supply rails. As a result, the output drivers fail one by one. Therefore, we check the charging data before we return the unit.

What to send with your module

Send the module with your contact details and the machine data. First, note the machine model and the serial number. Then add the fault codes your technician reads on site.

Moreover, tell us how the failure appears during work. For example, some units only fail when the machine warms up. As a result, our bench can reproduce the same condition.

What happens before your Caterpillar 607-2611 control module repair starts

We first diagnose the unit and report what we find. However, if the module is not repairable, or if no problem appears, the diagnostic cost is 200 dollars. In that case, we process a partial refund for the difference.

Warranty and technical support

A one year warranty backs every repair we deliver. Also, our team answers technical questions before and after the job. For example, you can describe the fault codes you read today.

Why trust our bench

Our engineering team carries more than 15 years of experience. Furthermore, we have rebuilt over 10,000 modules to date. Our simulation equipment reproduces the real machine signals during testing.

Order your Caterpillar 607-2611 control module repair

Ready to start? First, read our ECM repair services process. Next, browse the full Caterpillar ECM range. Finally, watch real bench tests on the ECM Engineering USA YouTube channel.

Ecm repair 4 steps

Additional information

Weight180 oz
Dimensions16 × 14 × 7 in