Caterpillar 2622878-01 | 10R5647 | C27 | ECM Repair

Original price was: $899.00.Current price is: $699.00.

Caterpillar 2622878, 2622878-01, 10R5647 | C27 | C9 ECM Repair Service.

Your ECM will be returned fully reconditioned, tested, and ready to be installed back to the exact vehicle it came off, saving you the time & expense of having a new ECM programmed to your machine.

 

Description

Caterpillar 262-2878 control module repair | 10R-5647 | C27

Our bench handles your Caterpillar 262-2878 control module repair and returns the unit ready to work. First, you ship the module to our shop in Orlando, Florida. Then our engineers diagnose every fault on the board.

After that, we rebuild the failed sections and test under load. As a result, the controller goes back on the exact machine it came from. Moreover, you avoid the cost of programming a new unit.

Caterpillar 262-2878-01 10R-5647 C27 control module repair

Part numbers covered by this service

  • 262-2878-01 and 262287801
  • 262-2878 and 2622878
  • 10R-5647 and 10R5647
  • 372-2905 and 3722905

Several references describe the same controller. Therefore, check the label on your module before you ship it. Also, the housing carries 120 pins.

Caterpillar C27 control module, 120 pin housing

Machines covered by the Caterpillar 262-2878 control module repair

The list below groups the Caterpillar families that use this controller. However, serial ranges matter, so send your machine model with the unit.

TRACK-TYPE TRACTOR

D6R III

WHEEL-TYPE LOADER

966H, 972H, 980H

ROAD RECLAIMER

RM-500

TRACK-TYPE TRACTOR

D9T, D6R III, D8T

PETROLEUM PRODUCTS

C15, C18

Loaders, dozers and scrapers also run this board. In addition, each family uses its own calibration. Therefore, we record the original data before we start.

PIPELAYER

PL83, 583T

OFF-HIGHWAY TRUCK

770

WHEEL-TYPE LOADER

966H, 988H, 972H, 980H

WHEEL TRACTOR-SCRAPER

657G

ENGINE – INDUSTRIAL

C15, I6 D500GC, C18, D550GC, C9, D600, GC D450GC, C15, C18, I6

Compactors, gensets and trucks close the list. Still, our bench follows one proven route on every unit.

EARTHMOVING COMPACTOR

825H, 825C, 836H, 826H, 826C

WHEEL DOZER

824H, 834H, 824C

ENGINE – GENERATOR SET

XQP500, C18, C15, POWER SYS

MOTOR GRADER24M, 140GTRUCK770

Caterpillar C27 ECM on the test bench

Symptoms that bring these units to us

Most boards arrive with a familiar story. For example, the engine cuts out and restarts later. Sometimes the technician simply loses the link with the module.

In addition, a blown fuse returns every time the key turns. A failing Caterpillar 262-2878 control module repair often shows more than one symptom. Moreover, oil or water intrusion damages the board over time.

How our bench tests the board

First, we open the housing and inspect the tracks under magnification. Then we measure the supply rails and the injector drivers.

Next, we replace the components that fail the test. After that, the board runs a full cycle on our simulator. As a result, an intermittent fault shows up before the unit leaves.

What to send with your module

Send the module with your contact details and the machine data. First, note the machine model and the serial number. Then add the fault codes your technician reads on site.

Moreover, tell us how the failure appears during work. For example, some units only fail when the engine warms up. As a result, our bench can reproduce the same condition.

What happens before your Caterpillar 262-2878 control module repair starts

We first diagnose the unit and report what we find. However, if the module is not repairable, or if no problem appears, the diagnostic cost is 200 dollars. In that case, we process a partial refund for the difference.

Warranty and technical support

A one year warranty backs every repair we deliver. Also, our team answers technical questions before and after the job. For example, you can describe the fault codes you read today.

Why trust our bench

Our engineering team carries more than 15 years of experience. Furthermore, we have rebuilt over 10,000 modules to date. Our simulation equipment reproduces the real engine signals during testing.

Order your Caterpillar 262-2878 control module repair

Ready to start? First, read our ECM repair services process. Next, browse the full Caterpillar ECM range. Finally, watch real bench tests on the ECM Engineering USA YouTube channel.

Caterpillar C27 module ready for return shipping

Ecm repair 4 steps

Additional information

Weight160 oz
Dimensions14 × 14 × 7 in